In this review I will tell about the Revapor kit from Vaporesso. If you do not want to read, then at the end of the review I will add a video version. The maximum power of this mod is 220 watts.
The kit is delivered in this miniature box, inside of which there is one more box, inside of which all the equipment is raspihana for two more boxes.
In the first box lies:
1. USB cable for charging and reflashing the mod.
2. Envelope with a guarantee card and a couple of pieces of paper.
3. Two instructions in different languages, including Russian.
In the second box lies:
1. A spare evaporator for two spirals. Designed for power from 30 to 70 watts (resistance 0.15 ohms). Also on the evaporator the recommended power range is indicated: 45-60W.
2. Spare glass, spare sets and a 510 drift adapter.
3. The tank with the installed 4x spiral evaporator (resistance 0.15 Ohm). The evaporator is designed for power 50-110W, the recommended power is 60-80W.
4. Boxing fashion
My story I’ll start with boxing fashion.
The button is plastic, large enough and is on the right side. You can click on the entire surface of the button, but to the bottom of the force of pressing increases. The center and the top are pressed with a little effort with a nice click.
In the upper part there is a connector. Screw here can be an atomizer with a diameter of up to 28 mm.
In the lower part of the mode there are holes for the discharge of battery gases.
The surface is glossy, looks good, but the fingerprints remain on it only so. On the front side there is a display. Below the display are three buttons: +, – and the menu. The fire button when using the menu is not used either. If you hold the fire button and the menu button at the same time, you can see the firmware version. Firmware can be updated by downloading it from the official website. Buttons plus and minus are not signed. Plus button – right, minus – left. Under the buttons is a USB port for charging and preproshivki mod.
Mod has a system of equalizing charge. When charging, the charge level and the remaining charge time for each battery are shown.
Consider the battery compartment. The mod is powered by two 18650 batteries. The fast charge mode is supported by a 2.5 A. The battery compartment cover is removed with a protrusion located at the base of the mod. The lid is fixed on six magnets, the fixation is quite dense, the lid does not hang. Three magnets are located in the lid and three in the casing. Batteries are tightly pressed into the compartments by brass spring-loaded mines. The tab for easy removal of batteries is missing, but the batteries are slightly bulging out of the compartment, so there is no problem in removing them.
The mode is switched on five times by pressing the fire button. The activation takes about three seconds.
The upper line of the display shows the battery level and mode of operation. The line below preheats, the resistance of the evaporator and the voltage applied to it. The next line shows the power. The tightening time is shown below, if the tightening time exceeds 10 seconds, the mode removes the voltage from the evaporator. In standby mode, you can display time on the screen. If there is no atomizer, CHECK ATOMIZER appears on the screen.
The following protections are also present:
1. USB port
protection 2. Low voltage
protection 3. Short circuit
protection 4. Low resistance of atomizer
protection 5. Temperature protection
6. Overcurrent protection
7. Protection against incorrect battery installation
The mod can operate with evaporators having a resistance of 0.05 to 5 ohms. The voltage applied to the evaporator can be from 0 to 9V.
Navigation in the menu is quite inconvenient. To switch modes, you need to hold down the menu button. Scrolling modes. The first is the varivatta mode. Next, the temperature control mode for stainless steel, nickel, titanium and two custom profiles. Then there is the bypass mode, which turns the device into a kind of mehmode. Next are the settings.
In addition, in the varivatta mode, pressing the “menu” button three times, you can adjust the heating curve. For the thermal monitoring mode, by doing the same, you can set either a heating curve or set your own TCR.
In the menu, by the way, you can not flip back, if you skipped the necessary point, you will have to scroll through the entire menu. To enter the desired menu item, you need to press the fire button three times.
In the settings, you can set the desired preheating, for VW mode. The default value is NORM. Next, you can set preheating for the thermal control mode. In the third menu item, you can set the time and date. Next, you can reset the settings to the default settings.
The fifth point is smart mode, which will automatically set the required power value. You can turn it off immediately and forget about it. In the sixth paragraph, you can set the time to turn off the screen. And the next item is the exit from the menu. Once again I will say that it is very inconvenient to use the menu.
Let’s look inside. The device is assembled on the OMNIBOARD 2.0 board. The device is very easy to disassemble, but if you need to remove the card completely, then you need to solder the wires going to the battery compartment and the connector.
And in the hand of the mod is very comfortable.
About the mod like everything, go to the tank.
The tank has a top dressing with a sliding lid. As I said, there is a 4-coil evaporator, designed for a power of 50-110 watts. Blowing down the bottom, for this on the sides are two holes. The ring of adjustment of a blowing turns smoothly and inside has the stopper, not allowing to turn around a tank. At the bottom is a standard 510 connector.
The dripper is fixed in the tank very tightly, this is facilitated by 2 orings. Also, the dripper is protected against splashing. The diameter of the tank is 26.5 mm. The capacity of the tank is 5ml. If capacity is required less, that is a version of the kit, in which the tank is used for 2ml.
Dimensions and weight of the mod: The
weight of the kit along with the batteries is 285.3 grams.
Unfortunately, there are no serviced evaporators for this tank. But there are several different options for non-services:
Advantages of the kit:
2. The presence of two different evaporators.
3. Protection from splashes in the dripper.
4. Good transfer of taste.
5. Balancing the batteries and indicating the time to complete the charge.
6. Accelerated charge with a current of 2.5A.
1. Working with the menu. Virtually all control one button. Very uncomfortable.
2. Glossy surface of the case.
Now You Can Get It On : Vaporesso Revenger Kit
Hot Sale Recommendation: